Sealer BR116

Description

A modified acrylic reskim system dispersed in a mixture of solvents. Its use to seal
and protect concrete substrate from impressing of dirt and provides an easier cleaning surface.

Area to Use

The product can be applied to most concrete surface.

Existing Concrete

Ensure that the substrate is clean and dry. Remove any efflorescence by an acid etch, high acid.

Typical Properties

Melting Point / Boiling Point ——— N/A
Vapor Pressure ———————— N/A
Specific Gravity ———————— 0.92
Flash Point —————————– 27°C
Solubility in water ——————— Insoluble
Solid(PBW) —————————- 25%
Appearance ————————— Matt Finish Seeker With Color
Flammability ————————– N/A

Application

Use as a concrete sealer, # Pour on with cone or tube

Packaging

SEALER BR 116 is packed in 5 liters or 18 liters pail.

Storage

Xyleen: Storage cool and dry,away from heat sources,flammable areas.

The representation and recommendation regarding the product are based on test, which we believe are reliable. We cannot accept responsibility or guarantee of success of your work as we have no influence or control over the method of application, site condition etc.

Description and Uses

Sealer BR 116 is an acrylic base concrete sealer designed for finishing new
interior or exterior concrete. It is also a durable sealer and finish coat for
refurbishing older colored, chemically stained, or uncolored concrete
flatwork. It gives the surface an attractive appearance and enhance depth
of color while offering an easy-to-maintain, matte finish and added
resistance to staining.

As a sealer and finish coating, Sealer BR 116 is helped in preventing
concrete dusting and reduces surfaces staining from materials such as
automotive grease, oil and food spills. It produces a low-maintenance,
easy-to-clean film, resistant to abrasion, weather and ultraviolet (UV)
radiation.

Warehouse, factory and many other interior colored or uncolored
concrete floors should normally be sealed to protect the concrete
surface and facilities clean up.

Recommended for:

• Concrete floor
• Textured concrete floor
• Coloured concrete floor
• Brick walls
• Slates
• Sandstone

Coverage

Sealer BR 116 must be applied full strength without thinning by roller,
airless sprayer or by brush. The coverage will very depending on the
method of application and the porosity and texture of the concrete. Two
thin coats are recommended for new uncoated concrete. One coat is
usually sufficient on concrete preciously coated with Sealer BR 116.As
a general rule of tumb, and 18 liter tin covers approximately 60m2 – 70m2.

Preparation

Before application, the concrete surface must be clean of all dirt, oil and
grease. Coatings and curing membranes, other than previously applied
Sealer BR 116,must be stripped. Failure to remove all contaminants and
coatings will cause appearance defects, adhesion loss, peel, and reduced
durability.

All washed or wet areas should be allowed to dry thoroughly before
application of Sealer BR 116.

Application

The coating must be applied thinly and uniformly. Immediately prior to use,
the liquid materials should be thoroughly mixed. Application of two coats id
recommended. The second coat should be applied after the first coat is
completely dry, a minimum of 4 hours. Sealer BR 116 must be allowed to dry
completely, normally a minimum of 12 hours after application of the second
coat. Finished surface should be protected from damage by other trades.

Coverage: 60m2 – 70m2 / 18 liter

Maintenance and Removal

Sealer BR 116 surfaces should be maintained by sweeping. Spills should be cleaned up when they occur. Dirt may be hosed off with water. On area subject to heavy use or more severe conditions, periodic general cleaning should be performed using a high-quality commercial detergent and automatic scrubber equipment.

A maintenance application of Sealer BR 116 should be made periodically
as the coating is worn off the surface. The need for maintenance coating
will be accelerated in area of heavy use.

It is not necessary to strip the previously applied coating unless film build
up is heavy of the surface cannot be cleaned sufficiency .Solvent can be
applied to remove existing Sealer BR 116.

Limitation

Sealer BR 116 must only be used in thin coats on surface adequately
textured for slip resistance unless used on surface previously coated
with the sealer, they must be porous to allow penetration. If applied
improperly or too heavily, the surface may whiten, peel, or become slippers,
particulars on pool decks or other area where water may collect and stand
on the surface.

Sealer BR 116 is a premium-quality sealer and finish coating, but like all
coatings, will require periodic maintenance and reapplication, Spills
should be removed promptly and floors cleaned regularly to minimize
possible staining and damage to the finish coat.